picnic table covers and pads and how to make it

78 picnic table covers and pads
78 picnic table covers and pads
78 picnic table covers and pads
picnic table covers and pads and how to make it. One of the pleasures in life is to eat simple meals in the outdoors when the weather is pleasant, whether you cook it on the grill, or just preparing a sandwich (sandwich)and a salad for a light lunch. Here are the steps to make your own functional picnictables are sturdy to enjoy your meal, and also great party.
Get a durable wood suitable for this project. Project in the photos using the southern yellow pine wood treated with pressure, and recycled from an old deck. Choose a premium wood, or even synthetic materials made from recycled plastic will produce a final project which is higher quality. The table that is created for this article has a length of 72 inches (183 cm), width 32 inches (81.3 cm) high, and 32 inch (81.3 cm), and the following materials are required:
14 boards size 2 x 6 x 72 inches (5 x 15.3 x 183 cm – thickness x width x length).
5 Board sizes 2 x 4 x 30 inches (5 x 10.2 x 76.2 cm – thickness x width x length).
1,361 12d galvanized nails g gram (8.89 cm) are hot dipped (replace with screws (deck) exterior 8.89 cm if you want stronger).
Cut the boards here, use a ruler or angled triangle to carpentry to make a right angle:
Cut 12 Board size 2 x 6 x 72 inches (5 x 15.3 x 183 cm). This will be the 6th Board table, 2 chairs, 4 rail Board Board Chair.
Cut 3 Board sizes 2 x 4 x 30 inches (5 x 10.2 x 76.2 cm) length from point to point in length, with 45-degree angles on each end.
Cut 4 boards size 2 x 6 x 35 inches (5 x 88.9 x 15.3 cm) length from point to point, with an angle of 25 degrees at each end. This will be the distance.
Note that you must also cut the Board retaining the diagonal below the surface of the table, but it is best to cut these boards to fit after all other upper already fastened together.
Put the boards of the top table at the horses, set so that the side that most good (at least the hole/eyes, cracking, etc.) facing down, as this will be the bottom surface ofthe table.
Pakukan Board 2 x 4 inch (5 x 10.2 cm) with 45-degree corner pieces to the bottom surface (leaf) table, give the distance of 4 inches (10 cm) from both ends, and the third was in the middle of the two ends. give your nails to hold it in place until the tables are reversed, after you finish nailing the upper part.
Position the boards of size 2 x 6 x 35 inches (5 x 88.9 x 15.3 cm) so that the short side of the pasa centered terminus (row Board) the surface of the table as shown in the photo, and the nail securely onto the tracks.
Measure 17 inches (43.2 cm) to top (down from the surface of a table when the table is reversed). Head to toe nail table at this sign, in a half-high spikes. This will be used support the Chair rail, you will install next
Put the seat rails (size 2 x 6 x 72 inches, or 5 x 15.3 x 183 cm) in the middle between the legs of the table while upside down, with the resting on the nail you have pairs of approximately 17 inches (43.2 cm). Nail the shelves.
Mark the middle section of the rail surface table and chair rail. Install one Board 2 x 4 inch (5 x 10.2 cm) diagonally between the two marks, as shown in the photo. Thiscut, and nails securely into place.
Behind your desk so that now stand on his feet. Lay your board your seat (once again, size 2 x 6 x 72 inches or 5 x 15.3 x 183 cm) seat rail, in which should be sticking out of the bottom of the table on each side. You’ll want to try them according to size, with sliding it in or out along the tracks until comfortable to you. When it is in the desired position, mark the location on the Board Chair outside, remove, and create an angle of 45 degrees with the saw on a rail so that no one will stand out from under the seats.
Put the back seat boards and nails. Navigate to the nail surface table tracks for security.
Cut all angles table surface at an angle of 45 degrees about 2 inches (5 cm) from the corner so that the angle is rounded (obtuse), to reduce the likelihood of people bump into it.
Rub with sandpaper and finish the table as you want. You can use a waterproof silicone sealing, namely polyurethane exterior (many products which claimed to be the actual degradation of polyurethane due to ultraviolet light), or semi transparent exterior wood pelitur for this purpose.
Place your desk in the shade and enjoy.

Leave a Reply

Your email address will not be published. Required fields are marked *